Konu "Design" için Çorlu Mühendislik Fakültesi Koleksiyonu listeleme
Toplam kayıt 19, listelenen: 1-19
-
Comparison of ANN and RSM modeling approaches for WEDM process optimization
(Walter De Gruyter Gmbh, 2021)In this paper, an effective process optimization approach based on artificial neural networks with a back propagation algorithm and response surface methodology including central composite design is presented for the ... -
Comparison of kinetics and costs of Fenton and photo-Fenton processes used for the treatment of a textile industry wastewater
(Academic Press Ltd- Elsevier Science Ltd, 2022)In this study, the treatment of textile industrial wastewater by Fenton and Photo-Fenton oxidation processes was investigated. For this purpose, the pH, Fe2+ and H2O2 concentrations with the best organic matter and color ... -
Creating an Alternative Production Line by Using a Simulation Technique in Duvet Cover Production
(Inst Chemical Fibres, 2018)In this study, the discrete-event system simulation technique was used in order to create smooth work flow on a duvet cover production line. In accordance with this purpose, a model of the work flow of a duvet cover was ... -
Development of a New Fabric Grading System with a Demerit Control Chart in the Apparel Industry
(Inst Chemical Fibres, 2021)Fabric defects are usually manually identified by quality control staff in the apparel industry. Control charts are an appropriate tool to achieve this goal. In this study, knitted fabric often used in an apparel factory ... -
Electronically controllable memcapacitor emulator employing VDCCs
(Elsevier Gmbh, 2021)Memcapacitors are become one of the research interest after the realization of memristors. Many researchers focused on the designing memcapacitor emulator because of some fabrication difficulties of this new element. In ... -
Evaluating silver-plated nylon (Ag/PA66) e-textiles for bioelectrical impedance analysis (BIA) application
(Iop Publishing Ltd, 2020)Bioelectrical impedance analysis (BIA) is an established method for assessing integrity of biotissue. Adapting BIA as a diagnostic tool to monitor electrophysiological activity gives rise to evidence-based objective ... -
Experimental analysis of the thermal behaviour of mezzanine floors in buildings with cavity wall insulation
(Academic Journals, 2010)In this study, the thermal behaviour of mezzanine beam-slab floor sections of buildings under temperate climate conditions was experimentally investigated. Data were obtained from measurements on buildings under service ... -
Experimental and numerical investigation of ground heat exchangers in the building foundation
(Pergamon-Elsevier Science Ltd, 2019)The current study proposes a novel method with the experimental and numerical studies for the ground source heat pumps, which are known as environment-friendly and efficient heating & cooling systems to overcome their ... -
Implementation of Microcontroller-Based Memristive Chaotic Circuit
(Polish Acad Sciences Inst Physics, 2017)In 1971, Leon Chua theoretically postulated that the memristor is the fourth fundamental circuit element, besides the three well-known circuit elements; namely, resistor, capacitor and inductor. For a long time, because ... -
A Low-Voltage Low-Power Full-Wave Rectifier Based on Dynamic Threshold Voltage MOSFET
(Amer Scientific Publishers, 2019)In this paper, a low-voltage and low-power dynamic threshold voltage Metal Oxide Semiconductor Field Effect Transistor (DTMOS) based current mode full-wave rectifier is presented. This presented rectifier contains only MOS ... -
A microcontroller-based ECG signal generator design utilizing microcontroller PWM output and experimental ECG data
(Institute of Electrical and Electronics Engineers Inc., 2018)Signal generators are commonly used in biomedical engineering studies. Biomedical circuits must often be tested using EEG, ECG etc. signals. The circuit tests are usually done by connecting electronic circuits to humans. ... -
A Numerical Investigation of Induced and Embedded Trench Installations for Large-Diameter Thermoplastic Pipes under High Fill Stresses
(Mdpi, 2023)The induced trench installation method is applied by placing material with high compressibility on rigid pipes to reduce the earth pressures acting on them. Although the performance of this method for rigid pipes has been ... -
Performance analysis and optimization of a radiating fin array
(Sage Publications Ltd, 2022)Space radiators are used to reject waste heat from power units, electronic devices, and various equipment in space vehicles. It is important that radiators can achieve the heat desired to be dissipated into space with the ... -
Planning of waste electrical and electronic equipment (WEEE) recycling facilities: MILP modelling and case study investigation
(Springer, 2015)Waste electrical and electronic equipment (WEEE) consist of many different substances some of which contain hazardous components and valuable materials. The recovery of WEEE plays a key role on environmental sustainability ... -
Prediction of full load electrical power output of a base load operated combined cycle power plant using machine learning methods
(Elsevier Sci Ltd, 2014)Predicting full load electrical power output of a base load power plant is important in order to maximize the profit from the available megawatt hours. This paper examines and compares some machine learning regression ... -
Response surfaces for compressive strength of concrete
(2013)The aim of total quality management (TQM) is to offer satisfactorily high quality products to customers for providing increased productivity and decreased costs. Various methods are used for process improvement, development ... -
Sigmoid Based PID Controller Implementation for Rotor Control
(IEEE, 2015)This paper presents a sigmoid based variable coefficient PID (SBVC-PID) controller design for Twin Rotor MIMO System (TRMS). The proposed SBVC-PID controller dynamically changes controller coefficients according to a ... -
Thermoforming behavior of 3D-printed PLA sheets
(Carl Hanser Verlag, 2020)Fused deposition modeling is one of the most well-known additive manufacturing methods. It might be considered the easiest way to produce particle reinforced composites or unreinforced sheets which are biodegradable and ... -
Vertical Variability of the Undrained Shear Strength of Golden Horn Clay
(Taylor & Francis Inc, 2009)In this study, a stochastic method was applied to investigate if there exists a statistical correlation between values of undrained shear strength at various vertical distances along Golden Horn. Therefore, the undrained ...