Bölüm "Fakülteler, Çorlu Mühendislik Fakültesi, Makine Mühendisliği Bölümü" Çorlu Mühendislik Fakültesi Koleksiyonu için listeleme
Toplam kayıt 122, listelenen: 1-20
-
3D finite element model for predicting manufacturing distortions of composite parts
(Sage Publications Ltd, 2016)A 3D finite element model has been developed for predicting manufacturing distortions of fibre-reinforced thermosetting composite parts. The total curing process is divided into three steps that correspond to the states ... -
Ağır Ticari Araç Hidrolik Direksiyonlarında Kullanılan Burulma Millerinin Burulma Katsayılarının Deneysel Olarak Belirlenmesi
(2022)Bu çalışmada ağır ticari araç hidrolik direksiyonlarında geri toplamayı sağlayan burulma millerinin burulma katılıkları teorik, numerik ve deneysel olarak hesaplanmıştır. Numerik çalışmada ANSYS programı kullanılarak burulma ... -
Bending and compression performance of composite tube reinforced foam core sandwich structures
(Applied Mechanics Laboratory, 2020)In some applications such as walls and roofs, it is important to supply low thermal conductivity and high bending stiffness to structures. Generally, foam materials are preferred, which have low thermal conductivity. ... -
Biçerdöverden tahrikli sap parçalama düzeneğinin çalışma performansına ilerleme hızı ve bıçak devirlerinin etkisi
(2013)Bu araştırmada, ayçiçeği hasadında, biçerdöver tablasının altına yerleştirilen ve hasat sırasında sapların parçalanmasını sağlayan parçalama düzeneğinin, sap parçalama etkinliği ile yakıt ve güç tüketim değerleri, ilerleme ... -
Buckling Characteristics of FGM Plates Subjected to Linearly Varying In-Plane Loads
(Springer, 2021)The critical buckling load for a FGM plate under a linearly distributed in-plane load is determined. Material properties of the plate vary exponentially across its thickness. The Ritz method is used to solve the equations ... -
Characterization of mechanically alloyed Fe based and MoNiAl+Al2O3 reinforced composites
(Walter De Gruyter Gmbh, 2021)Fe-MoNiAl-Al2O3 powders were mechanically alloyed by a SPEX type attritor. The Fe based composite samples were reinforced with complex mechanically alloyed Fe-MoNiAl-Al2O3 particles in different ratios and Fe matrix ... -
Compaction Pressure and Density Profile in Pile-Type Silos
(Corvinus Univ Budapest, 2019)The main aim of this study is to investigate the compaction pressure and density profile, and to determine the effectiveness of the compaction process applied to the pile-type silos. Chopped material was compacted into a ... -
COMPARATIVE INVESTIGATION OF Fe3O4, Fe3O4@HA AND Fe3O4@AC NANOPARTICLES ON DYES ADSORPTION
(Gheorghe Asachi Technical University of Iasi, Romania, 2022)In this study, the removal of Methylene Blue (MB) and Methyl Orange (MO) dyestuffs from aqueous solutions via adsorption by using magnetic nanoparticles of Fe3O4, Fe3O4@HA and Fe3O4@AC synthesized under laboratory conditions ... -
Comparative performance analysis of building foundation Ground heat exchanger
(Pergamon-Elsevier Science Ltd, 2020)The aim of this work is to improve the performance of Ground-Source Heat Pumps (GSHPs) by placing the heat exchanger pipes in the soil under the building foundation and in the building foundation reconstructed in Turkey. ... -
A composite sandwich plate with a novel core design
(Elsevier Sci Ltd, 2018)In this study, a new core design is introduced for sandwich composite structures. Its strength and failure behavior are investigated via three-point bending tests. E-glass-fiber-reinforced epoxy resin is selected as the ... -
Conventional and microwave drying of hydrocarbon cutting sludge
(Wiley, 2019)The purpose of this article is to investigate the drying kinetics and determine the effectiveness of conventional and microwave drying processes for drying of hydrocarbon cutting sludge which is one of the most important ... -
Design of a real-sized composite drive shaft and critical points from beginning to end
(Applied Mechanics Laboratory, 2020)In this study, the replacement of a metal drive shaft by a composite counterapart was investigated. The drive shaft considered here is a thin walled tube with an internal diameter of 60 mm and a length of 1200 mm. These ... -
Design of air cooling unit with PCM
(Institute of Physics Publishing, 2019)In this paper a heat absorption unit has been designed to cool the entering hot air. For this aim, five slabs of PCM (Phase change material) have been used inside the cooling unit. The velocity and temperature values of ... -
Design of Semisphere Solar-Microwave Hybrid Dryer and Drying Performance of Zucchini
(Tarbiat Modares Univ, 2019)In this work, performance of a newly designed hybrid dryer was investigated. Drying was done with the support of solar energy to microwave conveyor dryer. By using collector, which was designed with semisphere shape for ... -
Determination of optimum operating conditions and simulation of drying in a textile drying process
(Taylor & Francis Ltd, 2013)In this study, drying behavior of viscose yarn bobbins was investigated experimentally to specify the optimum drying conditions and a drying model was proposed for simulation of drying. The experiments were conducted in a ... -
Determination of some drying parameters of carrot dried using microwave method
(TUBITAK, 2020)In this study, moisture content, drying time, the diffusion coefficient, activation energy, drying rate, drying efficiency and the energy consumed during the drying of carrot were determined by using the designed microwave ... -
Determination of the Effects of Rotation Speed and Forward Speed on Combine Harvester Driven Stalk Chopper Assembly Operating Performance
(Ankara Univ, Fac Agr, 2013)In this research, it was investigated how the combine harvester forward speed and the rotation of blades during sunflower harvest affect chopping efficiency and fuel and power consumption of the chopping apparatus placed ... -
Developing pneumatic control for a manual electrical resistance spot welding machine
(2010)Bu çalışmada; tarım makineleri imalatında kullanılan, manüel kontrollü elektrik direnç nokta kaynak makinesi, yeniden revize edilerek otomasyona uygun hale getirilmiştir. Sistemin dönüştürülmesinde pnömatik devre elemanlarından ... -
Development of a chopper unit for chopping of sunflower stalk during harvesting by combine harvester
(2013)The aim of this research was the development of a chopping unit, which is placed under the header of a combine harvester. In this way, stalks can be chopped during harvesting and this will be useful in respect to saving ... -
Development of a Prototype Machine Shop Safety System for Vocational Training
(Gazi Univ, 2015)In this research, a sample of machine shop safety automation was designed in order to prevent occupational accidents taking place in machine shop environments. The developed prototype system is a special occupational safety ...