Başlık için Çorlu Mühendislik Fakültesi Koleksiyonu listeleme

Metallic composition and source apportionment of fine and coarse particles using positive matrix factorization in the southern Black Sea atmosphere

Tecer, Lokman Hakan; Tuncel, Gürdal; Karaca, Ferhat; Alagha, Omar; Süren, Pınar; Zararsız, Abdullah; Kırmaz, Rıdvan (Elsevier Science Inc, 2012)

In this study, coarse- (PM2.5-10) and fine (PM2.5) fraction aerosol samples were collected using a dichotomous sampler, and their metallic composition (Mg, Al, Ti, Ca, Cr, Cu, Fe, K, Mn, Ni, Pb, and Zn) were analyzed using ...

Metallurgical characterization of mechanically alloyed MoNiAl-WC reinforced Fe matrix composite

Teker, Tanju; Yılmaz, Serdar Osman (Carl Hanser Verlag, 2020)

MoNiAl-WC reinforced Fe matrix composites were obtained by mechanical alloying. The effect of various reinforcement ratios on microstructure change, elemental characterization and phase transformation were examined by using ...

A methodology for memristance calculation

Mutlu, Reşat; Karakunal, Ertugrul (Tubitak Scientific & Technical Research Council Turkey, 2014)

A memristor is a newly found fundamental circuit element whose behavior can be predicted using either the charge-dependent function called memristance or the flux-dependent function called memductance. Therefore, it is ...

Metilen mavisinin atık ZnO katalizörü ile fotokatalitik arıtımı

Çifçi, Deniz İzlen (2017)

Bu çalışmanın amacı, metilen mavisinin fotokatalitik oksidasyon prosesi ile gideriminde, katalizör olarak metal atıkları geri dönüşüm endüstrilerinden oluşan ZnO içerikli atıkların kullanılabilirliğinin araştırılmasıdır. ...

Micro-Computed Tomography as a Tool to Investigate the Deformation Behavior of Particulate-Filled Composite Materials

Çınar, Kenan; Güven, İbrahim (Asme, 2018)

Micro-computed tomography (CT) was used as a tool to investigate the deformation behavior of particulate-filled composite materials. Three different shapes of glass fillers (spherical, flake, and fiber) and filler mass ...

A Microcontroller Implementation of Hindmarsh-Rose Neuron Model-Based Biological Central Pattern Generator

Yener, Şuayb Çağrı; Mutlu, Reşat (Institute of Electrical and Electronics Engineers Inc., 2019)

Central Pattern Generator (CPG) has an important role in controlling the locomotion part of the animals. Bio-inspired Central Pattern Generators can find application areas in robotic and control applications. FPGA ...

A microcontroller-based ECG signal generator design utilizing microcontroller PWM output and experimental ECG data

Yener, Şuayb Çağrı; Mutlu, Reşat (Institute of Electrical and Electronics Engineers Inc., 2018)

Signal generators are commonly used in biomedical engineering studies. Biomedical circuits must often be tested using EEG, ECG etc. signals. The circuit tests are usually done by connecting electronic circuits to humans. ...

Microelements in the Lands of the Azerbaijan Republic

Sahmurova, Aida; Öngen, Atakan (Scibulcom Ltd, 2006)

Microelements are necessary to support life. However, in larger or lower amounts, they may become more important and critical. They may be accumulated in biological systems and become a significant health hazard. The main ...

Microhardness evaluation of enamel adjacent to an improved GIC sealant after different enamel pre-treatment procedures

Haznedaroglu, E.; Sözkes, Sarkis; Menteş, Süleyman Ahmet (Ariesdue Srl, 2014)

Aim This in vitro study was carried out to evaluate the microhardness of enamel adjacent to a glass ionomer cement (GIC) with high fluoride content used as a sealant (Fuji Triage, GC Corp., Japan) after laser, bur or air ...

Micromechanical modeling of particulate-filled composites using micro-CT to create representative volume elements

Güven, İbrahim; Çınar, Kenan (Springer Heidelberg, 2019)

A method based on X-ray micro-CT was introduced to create realistic representative volume elements (RVE) for particulate-filled composite materials. The method is applicable to most composite systems, and can be utilized ...

Micromechanical modeling of particulate-filled composites using X-ray computed tomography

Güven, İbrahim; Çınar, Kenan (DEStech Publications Inc., 2017)

Glass fillers with different shape and mass fractions were considered to demonstrate the wide range of applicability of micro-CT imaging. It is shown that micro-CT technique can be used to create realistic RVEs for two-phase ...

Microplastic Release from Domestic Washing

Çelik, Suna Özden (2021)

Plastics have been used by human beings in a wide variety of materials. Recently, microplastics, either primary or secondary, are encountered in different part of the environment on a global scale. One of the common type ...

MICROSTRUCTURE AND WEAR PROPERTIES OF FeCrC, FeW AND FeTi MODIFIED IRON BASED ALLOY COATING DEPOSITED BY PTA PROCESS ON AISI 430 STEEL

Teker, Tanju; Karataş, Selçuk; Yılmaz, Serdar Osman (Polska Akad Nauk, Polish Acad Sciences, Inst Metall & Mater Sci Pas, 2014)

The plasma transferred arc (PTA) process was used for developing wear resistance of AISI 430 steel substrate. Appropriate quantities of FeCrC, FeW and FeTi powders were combined to create conditions that synthesized M7C3 ...

Microwave Drying Behaviour of Tomato Slices

Çelen, Soner; Kahveci, Kamil (Sage Publications Ltd, 2013)

In this study, microwave drying behaviour of apple slices was investigated experimentally to determine the effect of microwave power on drying, energy consumption and colour quality. Microwave drying behaviour was simulated ...

Microwave energy assisted carbonization of nanostructured conducting polymers for their potential use in energy storage applications

Poyraz, Selçuk; Flogel, Marissa; Liu, Zhen; Zhang, Xinyu (Walter De Gruyter Gmbh, 2017)

Three well-established one-step approaches, namely, conducting polymer (CP) nanofiber (NF) synthesis by NF seeding, CP nanoclip (NC) synthesis by oxidative template, and microwave (MW) energy-assisted carbonization were ...