Bölüm "Meslek Yüksekokulları, Çorlu Meslek Yüksekokulu, Makine ve Metal Teknolojileri Bölümü" Scopus İndeksli Yayınlar Koleksiyonu için listeleme
Toplam kayıt 15, listelenen: 1-15
-
4E analysis of an underfloor heating system integrated to the geothermal heat pump for greenhouse heating
(Scientific And Technological Research Council Turkey, 2022)In this study, 4E (energy, exergy, exergoeconomic, and exergoenvironmental) analysis of an underfloor heating system integrated with the geothermal heat pump of a greenhouse with a usage area of 90 m(2) has been made. When ... -
Assessment of CO2Emissions Reduction Based on Different Insulation Materials in Residential Buildings: Example from Turkey
(IOP Publishing Ltd, 2021)In this study, the reduction of CO2 emissions caused by energy savings due to thermal insulation materials applied to the exterior of buildings was investigated. The study includes the evaluation of four different insulation ... -
Determination and Modeling of Optimum Insulation Thickness for Thermal Insulation of Buildings in All City Centers of Turkey
(Springer/Plenum Publishers, 2021)In this study, research has been carried out in which the optimum insulation thickness for the thermal insulation of buildings in all city centers of Turkey is determined according to life cycle cost analysis. Besides, the ... -
Determination of Drying Behaviour in Industrial Type Convectional Dryer and Mathematical Modelling
(Vinca Inst Nuclear Sci, 2020)In this study, the performance of a stenter (ram machine) that enables the drying of textile products with hot air is theoretically modelled with a diffusion model derived from Fick's second law. The experimental study was ... -
Effect of Zr Concentration on the Microstructure and Mechanical Performance of Porous Ti-Zr System by Powder Metallurgy
(Trans Tech Publications Ltd, 2022)In this study, porous binary Ti-(x)Zr alloys of nominal Zr contents (x=10, 20 and 30 at. %) with differing porosities were manufactured, using powder metallurgy with compaction conducted under a pressure of 300MPa and ... -
Evaluation of feasibility analyses for different hub heights of a wind turbine
(Erol Kurt, 2022)In this study, techno-economic and environmental feasibility analyses of a wind turbine for different hub connection heights were investigated using RETScreen Expert energy analysis program. Çerkezköy district of Tekirda? ... -
Experimental examination and theoretical modeling of drying behavior in the ram machine
(Taylor & Francis Inc, 2020)In this study, drying behavior of a ram machine, basically used for drying of textile products with hot air, was experimentally examined and the drying behavior was theoretically modeled by the first order kinetic model ... -
Fabrication, characterization, and in vivo biocompatibility evaluation of titanium-niobium implants
(SAGE Publications Ltd, 2021)In this study, biocompatible titanium-niobium (Ti-Nb) alloys were fabricated by using powder metallurgy methods. Physical, morphological, thermal, and mechanical analyses were performed and their in vivo compatibility was ... -
Investigation of Energy Saving Potential in Buildings Using Novel Developed Lightweight Concrete
(Springer/Plenum Publishers, 2020)In this study, three different composite materials were produced from mixtures of natural and waste materials in different proportions. The produced composites were used to determine the insulation thickness of exterior ... -
Investigation of structural and optical properties of pure ZnO and co-doped ZnO:Al:Mnx (x=1%, 2%, 3%, 5% at.) semiconductor thin films and electrical properties of produced diodes
(Gazi Universitesi, 2023)In this work, undoped and co-doped ZnO:Al:Mn semiconductor thin films and p-type Si diodes were produced via sol-gel technique method. The morphological and optical properties of the produced thin films were investigated ... -
Modeling of CO2 emissions via optimum insulation thickness of residential buildings
(Springer, 2021)The present study aims to determine and model CO2 emissions based on the energy savings through the thermal insulation applied to the external walls of the buildings for eighty-one different zones using four diverse thermal ... -
Simulation and thermodynamic analysis of a hot-air textile drying process
(Taylor & Francis Ltd, 2015)This paper is concerned with the simulation of drying behavior of wool yarn bobbins and also determination of the optimum operating conditions by using thermodynamic analysis. Firstly, experimental drying behavior of wool ... -
Structural and optical properties of pure ZnO and Al/Cu co-doped ZnO semiconductor thin films and electrical characterization of photodiodes
(Walter de Gruyter GmbH, 2021)Nano-structured semiconductor thin films and p-type Si photodiodes were fabricated with the sol-gel spin coating technique using pure ZnO and co-doped ZnO:Alx:Cuy with x = 1 at.-%, y = 1, 2, 3, 5 at.-%. The structural and ... -
A study on the phase transformation behaviour of Cu-20wt.Sn alloy produced using powder metallurgy method: Experimental and molecular dynamics modelling
(Elsevier B.V., 2020)In this study, Cu-20wt.Sn alloy was produced by powder metallurgy (PM) method by using high purity element powders. The phases in the microstructure of the produced alloy were determined by XRD study. The phase transformation ... -
Thin-Layer Drying Modeling in the Hot Oil-Heated Stenter
(Springer/Plenum Publishers, 2020)Although the drying processes have an important place in the textile industry in terms of drying or various textile finishing applications, they are considered as an expensive process in terms of energy and time consumed. ...