Bölüm "Fakülteler, Çorlu Mühendislik Fakültesi, Makine Mühendisliği Bölümü" için listeleme
Toplam kayıt 130, listelenen: 101-120
-
Prediction of heat transfer characteristics in a microchannel with vortex generators by machine learning
(Walter De Gruyter Gmbh, 2023)Because of the prompt improvements in Micro-Electro-Mechanical Systems, thermal management necessities have altered paying attention to the compactness and high energy consumption of actual electronic devices in industry. ... -
Prediction of Wall Thickness Distribution in Simple Thermoforming Moulds
(Assoc Mechanical Engineers Technicians Slovenia, 2014)Thermoforming is widely used in manufacturing industries to produce large and labour-intensive products. Compared to other manufacturing techniques, thermoforming is an extremely efficient process that is suitable for ... -
A Prototype Downdraft Gasifier Design with Mechanical Stirrer for Rice Straw Gasification and Comparative Performance Evaluation for Two Different Airflow Paths
(Ankara Univ, Fac Agr, 2018)In this research, a prototype downdraft throatless gasifier was designed with a mechanical stirrer. The gasifier was designed for gasification of rice straw pellets. The diameter of the reactor was 350 mm and a nominal ... -
Quantifying the delamination of L-shaped composite laminates under low velocity impact using x-ray computed tomography
(DEStech Publications Inc., 2018)Low velocity impact response and failure behavior of L-shaped composite laminates were investigated. The composite laminates with variable thickness, stacking sequences, and corner radius were manufactured using autoclave ... -
Research on the fire endurance of the silica sand membrane
(Institute of Physics Publishing, 2019)In this study, the fire endurance, density, low-temperature deflection, penetration and ring-ball method tests of the membrane produced throughout the mixing of Bitumen, IPP (isotactic polypropylene), LDPE (Low-density ... -
A review of new technologies in valve systems of internal combustion engines and their effects
(Institute of Physics Publishing, 2019)Efficient use of energy is becoming increasingly crucial due to global warming and depleting fossil fuel sources. Automotive manufacturers aim for fuel economy, reduction of exhaust emissions, durability, volume and weight ... -
A Review on the Mechanical Modeling of Composite Manufacturing Processes
(Springer, 2017)The increased usage of fiber reinforced polymer composites in load bearing applications requires a detailed understanding of the process induced residual stresses and their effect on the shape distortions. This is utmost ... -
Saha Koşullarında Mısır Silajı Yapımında Silo İçi Basınç Değişimlerinin Belirlenmesi
(2018)Silolama sırasında silaj materyale uygulanan sıkıştırma işlemi silaj kalitesi açısından önemlidir. Doğru birsıkıştırma işlemi için, silo içerisinde tüm materyalin eşit ve yeterli oranda sıkıştırılması gereklidir. Bu ... -
Selected Mechanical Properties and Bruise Susceptibility of Nectarine Fruit
(Taylor & Francis Inc, 2012)This research was conducted to evaluate some mechanical properties and bruise susceptibility of nectarine (Prunus persica variety). Compression and impact tests were conducted to determine the mechanical properties and the ... -
Simulation and thermodynamic analysis of a hot-air textile drying process
(Taylor & Francis Ltd, 2015)This paper is concerned with the simulation of drying behavior of wool yarn bobbins and also determination of the optimum operating conditions by using thermodynamic analysis. Firstly, experimental drying behavior of wool ... -
Simulation of Drying Behavior of Cotton Bobbins by a Simultaneous Heat and Mass Transfer Model
(Trans Tech Publications Ltd, 2011)In this study, the drying process of cotton bobbins for different drying air temperatures has been simulated by a simultaneous heat and mass transfer model. In the model, the mass transfer is assumed to be controlled by ... -
Single Layer Drying Behavior of Apple Slices in a Microwave Dryer
(Trans Tech Publications Ltd, 2011)In this study, the drying behaviour of single layer apple slices of 5mm thickness in a microwave dryer was investigated experimentally for four different microwave power levels (90 W, 180 W, 360 W and 600 W) and suitability ... -
Sliding wear behavior of FeCrC reinforced and Ni-based composites produced by mechanical alloying technique
(Redakcia Kovove Materialy, 2018)The study presents the behavior of FeCrC particulates reinforced and Ni-based composites produced by a mechanical alloying process in the presence of friction and wear. Ni, Al and M7C3 powders having 100 mu m size were ... -
A software for calculation of optimum conditions for cotton, viscose, polyester and wool based yarn bobbins in a hot-air bobbin dryer
(2012)In this study, a software has been developed to predict the optimum drying conditions of viscose, wool, polyester and cotton based yarn bobbins for drying in a pressurized hot air dryer. For this purpose, firstly, a suitable ... -
Suitability of drying models in defining hotair drying behaviour of polyester based yarn bobbins
(2011)In this study, the suitability of several empirical and semi-empirical drying models available in the literature to define drying behaviour of polyester based yarn bobbins has been investigated. For this purpose, firstly, ... -
Synthesis and structural characterization of Fe based Ti+Ni3Al+Al2O3 reinforcement composite produced by mechanical alloying
(Consejo Superior Investigaciones Cientificas-Csic, 2020)The Fe-based Ti+Ni3Al+Al2O3 powder mixture is mechanically alloyed in a Spex ball mill. Composites with Fe-based Ti+Ni3Al+Al2O3 addition were produced at 1000 degrees C sintering temperature for 1 h sintering time. The ... -
Thermoforming behavior of 3D-printed PLA sheets
(Carl Hanser Verlag, 2020)Fused deposition modeling is one of the most well-known additive manufacturing methods. It might be considered the easiest way to produce particle reinforced composites or unreinforced sheets which are biodegradable and ... -
Thermophysical parameter estimation of a wool bobbin during convective drying process
(Taylor & Francis Ltd, 2010)In this work, an inverse heat transfer problem was solved by using experimental temperature data to estimate the effective thermal properties as well as the effective heat transfer coefficients on the inner and outer ... -
Three dimensional mechanical buckling of FG plates with general boundary conditions
(Elsevier Sci Ltd, 2013)The mechanical buckling analysis of rectangular functionally graded plates under different axial loadings is considered. The analysis is based on the small strain elasticity theory with different boundary conditions. The ... -
Three dimensional shear buckling of FG plates with various boundary conditions
(Elsevier Sci Ltd, 2013)In this paper, the buckling of functionally graded plates under shear are considered for various boundary conditions. The buckling results obtained by using Ritz method based on the three-dimensional linear elasticity ...